Fosroc Construction Chemical And Products

Product Details:

Specification clauses:
The steel reinforcement primer shall be Nitozinc Primer, a
two component zinc rich epoxy primer. The primer shall be an
''active'' type capable of avoiding the generation of incipient
anodes in the immediately adjacent locations. It shall be fully
compatible with the Renderoc system of concrete repair.

Application Instructions:
Preparation Saw cut or cut back the extremities of the repair locations to a depth of at least 10mm to avoid feather edging and to provide a square edge. Break out the complete repair area to a
minimum depth of 10mm up to the saw edge. Clean the surface and remove any dust, unsound or contaminated material, plaster, oil, paint, grease, corrosion deposits or algae. Where breaking out is not required, roughen the surface and remove any laitance by light scabbling or grit sand blasting.

Product Details:

Uses:
Renderoc RG Spl is used for repairs to damaged reinforced
concrete elements, particularly where access is restricted and
where vibration of the placed material is diffi cult or impossible.
It is suitable for various structural strengthening measures
such as encasement build-ups, jacketing , piletop encapsula-
tion resin system, etc.

Advantages:
Gaseous expansion system compensates for shrinkage and settlement in the plastic state.
Can be pumped or poured into restricted locations
Fluidity to allow for placement without vibration.
Pre-bagged to overcome site-batched variations.
Rapid strength gain to facilitate early reinstatement.

Description:
Renderoc RG Spl is supplied as a ready to use blend of dry
powders which requires only the site addition of clean water to
produce a free-fl owing non-shrink repair micro concrete. The
material is based on Portland cements, graded aggregates
and fi llers, and additives which impart controlled expansion
characteristics in the plastic state, while minimising water de-
mand. The low water requirement ensures high early strength
and long-term durability.

Product Details:

If the repair area exceeds 2.5 m , consideration
should be given to the use of mass fill by means of either
Renderoc HS Xtra spray applied mortar or Renderoc LAXtra
micro-concrete.

Other Detail:

• In situations where a substrate/repair barrier is required, or enhanced bond strength/working time is required, or where the substrate is likely to be permanently wet or damp (e.g. seawalls, quays etc.), Nitobond EP epoxy bonding agent should be used.

• Under no circumstances should part bags be used or additional water be employed. Either of these two actions will adversely affect material performance.

Application Instructions:

• Renderoc HSXtra should only be mixed and applied in strict
• accordance with the product Method Statement, a copy of
• which may be obtained from your nearest Fosroc office.

Product Details:

Mixing:
The entire contents of the hardener can should be poured into the base container and mixed for 2-3 minutes or until uniform colour is achieved. Once mixed, the material must be used within the specifi ed pot life (see under Properties). After this time, unused material will have stiffened and should be discarded.

Placing:
Ensure that the grout can be placed within its pot life. Continuous grout fl ow is essential. Suffi cient grout must be available prior to starting and the time taken to pour a batch must be regulated to the time taken to prepare the next one. Pouring should be from one side of the void to eliminate air entrapment. The hydrostatic head must be maintained at all times so that a continuous grout front is achieved.

Cleaning:
All tools and equipment should be cleaned immediately after
use with Nitofl or Sol.

Limitations:
Grouts should not be placed in any unrestrained situation, i.e. base plate plinths, etc. Failure to comply may lead to crack development in the grout.

Product Details:

Uses:
Provides a free flowing grout, for use where physical properties and chemical resistance of the hardened grout are of utmost importance. It is suitable for a wide range of heavy duty applications including :

• Underplate grouting to substantial structural elements.
• Base plate grouting in dynamic load situations such as
• turbines and other reciprocating machinery.
• Heavy industrial applications in steelworks, refineries
• chemical plants and electroplating works.
• Structural infill where very high strength is required.
• Rail track applications, to support heavy cranes,or ontransporter rails

Advantages

• Excellent durability - high compressive, flexural and tensile
• strengths ensure a long working life.
• Cost effective - high early strength gain promotes minimum
• downtime and early commissioning of plant.
• User friendly - simple, full pack mixing to ensure that the
• performance characteristics are achieved.
• Versatile - suitable for a wide range of loading situations
• including repetitive dynamic loads.
• Excellent in service performance - non-shrink capability
• ensures full surface to surface contact.

Product Details:

Description:
Starpatch Non Metallic Floor Hardener Is A Specially Formulated Product Designed For Flooring Work. It Provides Greatly Improved Impact And Abrasion Resistance. Starpatch Non Metallic Floor Hardener Will Provide Hard Durable Floor Surfaces. Starpatch Non Metallic Floor Hardener Is Plasticized To Provide Easier Placing And Finishing Characteristics.

Recommended For:
Use As A Surface Hardener For Concrete Floors That Are Subject To Wear Due To Abrasion Or Impact From Light To Heavy Traffic.
Can Be Used Interior Or Exterior.

Application Procedure:

• Apply Starpatch Non-Metallic Floor Hardener In Two Separate Dry Shake Applications Of Equal Weight.
• Apply The First Shake After Sufficient Floating Has Been Carried Out To Bring Enough Moisture To The Surface For Combining With Starpatch Non-Metallic Floor Hardener.
• When The Moisture From The Concrete Dampens The First Application Of Dry Shake, Re-Float The Floor Surface To Obtain Thorough Mixing Of The Shake With Mortar From The Concrete.
• Immediately Following This Floating, Evenly Distribute The Remainder Of The Dry Shake Over The Concrete Surface.
• Carry Out A Final Floating To Obtain Thorough Mixing With The Previously Applied Surface Treatment. Avoid Excessive Floating.
• Where Colour Uniformity Is Of Importance Use Only Stainless Steel Trowels For Hard Trowelling.

Product Details:

Uses:
For improving and bonding floor toppings, mortars and renders
As a bonding agent for Renderoc and other cementitious mortars
Polymer modified mortars and screeds for reinstatement of worn out/damaged concrete
Polymer modified concrete for improving the impermeability and there by enhancing the waterproofing property

Advantages:

• Good adhesion - Provides good bond to concrete, masonry, stone work, plaster and block work.
• Increased strength - Improves tensile and flexural properties of mortar.
•  Versatile - Compatible with all common hydraulic cements
• User friendly - application by brush/spray
• Improves cohesion - No bleeding and segregation

Description:
Nitobond AR Std. is a single component latex acyrlic polymer emulsion used as bonding aid cum cement modifier with waterproofing property.

Product Details:

Uses:
For modifying and improving bonding of floor toppings, renderings and mortars; repair of worn, damaged and spalled concrete, repair of large cracks; polymer modified floor screeds; waterproof plasters for masonary and slurries.

Advantages:

• Simple to use - Single component, gauged as required.
• High - Provides excellent bond to concrete, adhesion plaster, masonry, stone work, etc.
• Improves -Gives weather resistant mortar with improved
• durability impermeability to chlorides and other harmful agents.
• Reduces - Provides waterproof screeds, plasters and Permeability slurries.
• Increases - Improved tensile and flexural properties strength allow thin applications.
• Versatile - Compatible with all common hydraulic cements.
• Cost effective - Nitobond SBR (Latex) is economical to use

Description:
Nitobond SBR(Latex) is modified styrene butadiene emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external applications too.

Product Details:

Uses:
Nitocote CM210 provides a cementitious, elastomeric wa- terproof coating with inherent crack-bridging ability. Typical applications include:

• Potable water retaining structures.
• Swimming Pools.
• Potable water excluding structures.
• Internal basement waterproofing.
• Drainage culverts.
• Wet areas: Kitchens, bathrooms, shower rooms
• Foundations in contact with ground water under saline conditions

Advantages:

•  Withstands high positive and negative hydrostatic pressures
•  Excellent crack accommodation before and after immer-sion
•  Approved for use in contact with potable water
• Excellent bond to concrete and masonry
•  Long working life
•  Easy application by brush, trowel or spray
•  Bonds to green or damp concrete

Product Details:

Thicker vertical sections may sometimes be possible dependent on the profile of the substrate and the volume of exposed reinforcing steel but should generally be built up in layers, when larger areas are being rendered, a checkerboard application technique is recommended.

Buildup:
If sagging occurs during application, the Nitomortar S should be completely removed and reapplied at a reduced thickness  on to the correctly reprimed substrate.

Finishing:
Nitomortar S is finished by the use of a wood float and closed  with a steel trowel. The completed surface should not be overworked

Over coating with protective / decorative finishes:
Nitomortar S is extremely durable and resistant to a wide range
of acids, alkalis and industrial chemicals and will provide
excellent protection to the concrete and embedded steel
reinforcement within the repaired locations. The surrounding
parts of the structure may benefit from the application of a
protective coating, thus bringing them up to the same protective
standard as the repair itself. Fosroc recommend the use of
the Nitocote range of epoxy resin, chemical resistant, protective
coatings.

Product Details:

Uses:
For sealing internal floor joints subject to heavy industrial use in factories, food processing areas, warehouses and maintenance facilities. Particularly suitable for sawn joints in long strip flooring and other large internal areas.

Advantages:

•  Load bearing for support of arrises under heavy wheel load
•  Good resistance to chemicals and hydrocarbon fuels
• Excellent adhesion without primer to dry clean concrete
• Pouring grade ensures ease of placing
• Suitable for use in wide joints
• Self levelling to produce uniform and neat joints

Description:
Nitoseal PU280 two-part pouring grade sealant is formulated
from a blend of epoxy and urethane polymers. The mixed
sealant is self levelling and can be poured directly into
horizontal joints to form a tough resilient seal possessing a
limited degree of flexibility.
Nitoseal PU280 is available in a range of attractive colours
with a separate colour pack providing visual mixing control

Product Details:

Uses:
Nitoflor Hardtop / Nitoflor Hardtop Standard provide a highly abrasion resistant surface to concrete floors by the dry shake- on method which ensures that the hardwearing surface bonds monolithically to the base concrete. They are ideally suited for all industrial areas subject to the heaviest traffic, e.g. loading bays, trucking lanes, car parks, workshops, machine shops, ramps and spillways.

Advantages:

• Non metallic - does not rust or stain.
• Provides a hard, abrasion resistant surface
• Forms monolithic bond with base concrete
• Easy and economical to apply

Description:
Nitoflor Hardtop / Nitoflor Hardtop Standard are quality controlled, factory blended powder which are ready to use on
site. They contain special hardwearing aggregates which have been selected for abrasion and wear resistant properties
as well as shape and size. These latter considerations, together with the use of high performance workability
admixtures, produces a material which is easy to trowel into the surface of fresh, wet concrete. Nitoflor Hardtop / Nitoflor
Hardtop Standard cure monolithically to provide a dense, non-porous surface which is extremely hardwearing and
abrasion resistant. Monolithic cure ensures that problems normally associated with thin 'granolithic' screeds, viz., shrinkage, cracking, etc., are completely overcome.

Product Details:

Brushbond Roof Guard:
Brushbond Roof Guard is a single component acrylic polymer modified, fibre reinforced high build easy roller / brushable coating available in different colours for application in multiple layers, minimum 3 layer application is recommended for best performance. Thickness of each coat shall be approximately 330 micron. The product can be applied directly on existing concrete, brickbat coba, and screed concrete even without removal provided the substrates are sound enough for application of the coating avoiding the risk of damage to the old roof associated while
removing of the existing overlays. The product provides a seamless, tough durable water resistant coating which can withstand light pedestrian traffic and also has excellent weather resistance for exterior applications.

Other Detail:

• Excellent barrier to carbon dioxide, chloride and sulphate ions.
• Allows water vapour to escape from the structure.
• High resistance to the effect of long-term weathering,
• Durable in all climate conditions including UV attack.
• Excellent bond to concrete and masonry.
• Good crack accommodation capacity.
• Minimum surface preparation needed and low labour

Product Details:

Uses:
 To reduce permeability of concrete and sand/cement mortar for use in basements, roof slabs and screeds, water retaining structures, external plastering, bathrooms and balconies.

Advantages:

• Easy to use- Simple application familiar to site operations
• High Quality - Traditional waterproofing material manufactured to latest standards.
• Workability - Improves workability

Standards compliance:

Conplast WP90 powder conforms to IS:2645 - 2003 and is
certified by the Bureau of Indian Standards.

Description:

Conplast WP90 powder is a fine, white powder ready for use with concrete or cement mortar mixes. Conplast WP90 powder is a traditional admixture to fill natural pores within the concrete or mortar matrix to reduce porosity and improve water tightness.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

Description:
Performance specifi cation Renderoc RG Spl is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-fl owing non-shrink repair micro concrete. The material is based on Portland cements, graded aggregates and fi llers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand. The low water requirement ensures high early strength and long-term durability. For larger repairs, the mixed Renderoc RG Spl may be modi-fied by the addition of 5mm to 12mm clean, graded, saturated surface dry aggregates at site. For exceptionally large repairs, the local Fosroc offi ce shall be consulted.

Advantages:

• Gaseous expansion system compensates for shrinkage
• and settlement in the plastic state.
• Can be pumped or poured into restricted locations.
• Fluidity to allow for placement without vibration.
• Pre-bagged to overcome site-batched variations.

Product Details:

Uses:
For the rapid temporary patching and plugging of concrete segments, concrete and brick tunnel linings, sewage systems, below ground access chambers, pipes, basements, foundations and mines.

Advantages:

• Emergency water-stopping capability
• Single component - only the addition of clean water is required
• Excellent bond to the substrate
• Low exotherm minimises thermal cracking

Description:
Renderoc Plug is supplied as a ready to use blend of dry
powders which requires only the site addition of clean water
to produce a highly consistent, rapid setting mortar which is
easy to apply in many difficult conditions. The material is
based on a blend of cements, graded aggregates, special
fillers and chemical additives which control the rate of set
and minimise the risk of thermal cracking.

Product Details:

Unrestrained Surface Area:
This must be kept to a minimum. Generally the gap width
between the perimeter formwork and the plate edge should
not exceed 150mm on the pouring side and 50mm on the
opposite side. It is advisable, where practical, to have no gap
at the flank sides.

Mixing and Placing:
For best results a mechanically powered grout mixer should
be used. When quantities up to 50kg are used, a heavy duty
slow speed drill (400-500 rpm) fitted with a paddle is suitable..
Larger quantities will require a heavy duty mixer.
To enable the grouting operation to be carried out continuously,
it is essential that sufficient mixing capacity and labour are
available. The use of a grout holding tank with provision to
gently agitate the grout may be required.

Placing:
At 30 C place the grout within 20 minutes of mixing to gain full
benefit of the expansion process.
Conbextra GP2 can be placed in thicknesses up to 100mm
in a single pour when used as an underplate grout.
For thicker sections it is necessary to fill out Conbextra GP2
with well graded silt free aggregate to minimise heat build up.
Typically a 10mm aggregate is suitable. 50 - 100% aggregate
weight of Conbextra GP2 can be added.

Product Details:

Application Guidelines:

A few Dos and Don'Ts Do's

• Measure water precisely
• Mix mechanically
• Use mixed grout within 30 minutes
• Clean concrete and steel surfaces thoroughly before
• grouting
• Build a strong, carefully designed leakproof shuttering
• Cure properly for at least 7 days.

Donts:

• Mix cement, sand, fibres, admixtures, etc., withConbextra AT
• Mix water more than specified
• Pour grout from two sides while grouting base plates.
• Pour grout from a height

Product Details:

Uses:
Recommended primer for Fosroc cementitious repair system. For improving and bonding floor toppings, renders and mortars; repair of worn, damaged or spalled concrete; polymer modified floor screeds.

Advantages:
Simply brush onto concrete as a primer. Single component,
gauged as required.

• High adhesion -Provides excellent bond to concrete, masonry, stone work plaster and block board.
• Increased strength - Improves tensile and flexural properties of mortar. Allows thin section applications.
• Versatile - Compatible with all common hydraulic cements
• Economical - Economical to use

Description:
Nitobond AR is a modified acrylic emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external applications.
 Nitobond AR is the recommended primer for the  cementitious repair system.

Product Details:

Uses:
Sealing movement joints in building and civil engineering structures, including superstructures, floors, basements and subways.

Advantages:

• Meets key international standards
• Forms a tough, elastic, rubber-like seal
• Accommodates continuous and pronounced cyclic movement
• Excellent adhesion to most common substrates, including
• primed concrete, glass, aluminium and stainless steel
• High resistance to ageing reduces physical damage due
• to climatic extremes

Description:
Thioflex 600 is available in gun and pouring grades. The gun grade is ideal for general application. It is packed in a ready to mix, 2.5 litre tin containing the base and curing agent in the correct proportions. The pouring grade for joints in horizontal surfaces is supplied in 5 litre packs with the base and curing  agent in separate tins.

Product Details:

Uses:
Brushbond TGP crystalline waterproofing system is used for waterproofing against the positive or negative sides of hydrostatic heads of water, for dampproofing, repairing cracks, plugging holes, sealing wall - floor joints and stopping active leaks in a wide variety of condtions including :

• Sewage treatment and water treatment plants, tanks, foundations, tunnels and manholes.
• Terrace garden, balconies, sunshades etc.
• Roof and Sunken slabs
• Industrial and office buildings
• Reservoirs, water holding structures etc.

Advantages:

• Meets the requirements as per ANSI/NSF Std 61 for suitability to potable water
• Penetrates concrete, seals capillary tracts
• Contains no chloride
• Easy to apply

Product Details:

Uses:
To minimise permeability and increase the waterproofing properties of concrete and cement sand mortars for critical applications like roof slabs and screeds, basements, external plastering, bathroom floors, water tanks, sumps, drains etc.

Advantages:

• Liquid admixture: Instant and complete dispersion throughout the mix. Uniform waterproofing throughout concrete matrix.
• High efficiency: Dramatic reduction in permeability of concrete/ mortar
• Improved workability: Improves compaction of concrete and mortar, even where harsh sands or aggregates are used.
• Improved concrete quality : Minimises porosity and honey combing. Produces dense homogenous concrete.

Description:
Conplast WL is a dark brown liquid based on lignosulphonates which mixes readily with water and therefore disperses evenly.

Conplast WL waterproofs by improving the quality of the concrete or mortar. It reduces the water demand for required workability and minimises segregation and bleeding. Thus it is more efficient compared to traditional powder waterproofers as its use results in two fold improvement of concrete or mortar.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

Latex acrylic polymer based cementitious coating
Uses: Provides passivating protection matrix to reinforcing stee
Advantages
?? Anticorrosive - protects from future corrosion
?? High adhesion - excellent bonding to all types of steel substrate
?? Cement based - compatible with concrete ?? User friendly - can be easily applied by brush
Description Nitocote AP35, a single component latex acyrlic polymer based emulsion is used for protecting steel reinforcement from corrosion. It only needs to be mixed with cement at site to produce an easily brushable coating.
Technical support Fosroc offers a technical support service to specifiers, end users and contractors, as well as on-site technical assistance in locations all over the country
Application instructions

Surface Preparation Any corroded steel in the repair area and all loose scale and corrosion deposits should be fully exposed. Steel should be cleaned to a bright condition paying particular attention to the back of exposed steel bars. Grit-blasting is recommended for this process. Where corrosion has occured due to the presence of chlorides, the steel should be high-pressure washed with clean water immediately after grit-blasting to remove corrosion products from pits and imperfections within its surface. Application The application of Nitocote AP35 acrylic primer must take place as soon as possible to a dry steel surface after completion of the preparation work but always within 3 hours. One full and unbroken coat of Nitocote AP35 acrylic primer shall be applied by suitable brush making sure the surfaces of the steel are properly coated. A small brush is generally suitable for this purpose. It shall be allowed to dry fully before continuing. If in doubt of having achieved an unbroken coating, a second application should be made as soon as the first coat is fully dry (generally between 45 minutes and one hour) The application of concrete repair materials should proceed as soon as the Nitocote AP35 acrylic primer is fully dry ( generally 45 mins. to 1 hour ). Minimum application temperature for Nitocote AP35 acrylic primer is 100 C. Equipment cleaning Immediately after use, all tools shall be washed with clean water.

Additional Information:

• Packaging Details: Nitocote AP35 acrylic primer is supplied in 1, 5 and 20 litre plastic containers

Product Details:

Uses:
For easy and stain free release of concrete moulds and formwork of all types. Particularly where wooden formwork is  used and de-moulding or stripping times exceed 24 hours.

Advantages:

• Non-staining : No cleaning of unsightly oil stains if plastering is not required.
• High quality : Produces really fair faced finish concrete.
• Versatile : Can be used on all types of moulds.
• Minimises cleaning : Makes cleaning of form faces between pours very easy.
• Concentrate form : Reduces storage and transport costs.
• Water based : Only requires water for dilution. Aids corrosion inhibition.

Description:
Reebol Emulsion Xtra is supplied as a pale amber liquid which turns white when diluted with water to produce a chemical release agent, combining the outstanding release properties of such materials with the economy of a conventional oil. It reacts with the alkali in the concrete to form a thin water repellent skin on the surface of the mould which enables easy stripping from the hardened concrete.

Product Details:

Preparation:
Any corroded steel shall be fully exposed and all loose scale and corrosion deposits shall be removed. Steel should be cleaned to a bright condition paying particular attention to the back of exposed steel bars. Grit-blasting is recommended for this process.
Where corrosion has occured due to the presence of chlorides, the steel should be high-pressure washed with clean water immediately after grit-blasting to remove corrosion products from pits and imperfections within its surface.

Mixing:
Both components shall be mixed until a homogenous mixture is obtained. It is important that both components are intermixed thoroughly and that no traces of the components remain unmixed. A slow speed heavy duty drill fitted with a paddle is recommended for mixing.

Application:
 The application of Nitozinc Primer must take place as soon as possible to a dry steel surface after completion of the preparation work but always within 3 hours.

Product Details:

Uses:
 The high elasticity, excellent bond and low water permeability of Nitoproof 600 make it ideal for a wide range of water/vapour proofing applications such as foundations, basements, tunnels, ground floors, suspended floors, car decks, roof terraces, balconies, patios, bridges, precincts, inspection pits, water retaining structures (not potable water), sewage works, and inverted roofs. The excellent chemical resistance of Nitoproof 600 makes it particularly suitable for tanking applications in areas where aggressive ground water conditions prevail.

Advantages:

• One component; ready to apply direct from the can
• Liquid application means details are simplified and there
• are no joints in the membrane
• Highly elastic, cures to give a permanently flexible resilient
• barrier over a wide range of temperatures
• Rapid installation; significantly reduces time spent on
• preparatory works and detailing

Description:
Nitoproof 600 single component pitch modified polyurethane cures by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane. It is supplied in a single grade to meet all site application methods and requirements. Nitoproof 600 is a medium viscosity grade (approximately 600 poise) for roller, squeegee or spray application to horizontal and vertical surfaces.

Product Details:

Uses:
Riba Clean RR is used as a rust remover from steel bars prior to encasing in concrete / microconcrete. It can also be used on ohter steel surfaces prior to coating with epoxy systems.

Advantages:
Rapid action
Safe with metals (except zinc and galvanised steel), wood, glass, plastic and rubber. No corrosive action. Penetrates oil and grease.

Description:
Riba Clean RR cleaning agent is a combination of acid
based material, corrosion inhibitors and dispersing agents
and is supplied as a clear green solution.

Technical Support:
Fosroc provides a technical advisory service to specifiers,
end-users and contractors as well as on-site technical
assistance in locations all over the country.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

Uses:
Provides an effective and economical method of waterproofing to concrete and masonry surfaces, by mixing with cement and application by brush.

Advantages:

• Non - toxic, non-flammable and user friendly
• Provides a tough, impermeable waterproof membrane
• Can be applied by brush, on horizontal and vertical surfaces
• Excellent adhesion to concrete and masonry surfaces

Description:
Hydroproof is formulated to be mixed with cement on site or simply brush applied over concrete or masonry surfaces to provide an effective waterproof membrane.

Areas of application:

• Roofs, terraces and balconies as a sandwich layer
• Pools and fountains
• Reservoirs and channels
• End walls subjected to rain

Product Details:

Uses:
As primer for applications of Thioflex to concrete to improve water immersed and early age bonding characteristics of the joint sealant and where compliance to EN 14188-2 is required.

Advantages:

•    Excellent adhesion to partially,or permanently,
•    water immersed concrete joints
•    Cold applied
•   Rapid drying

Description:
Fosroc Primer 7E is a two-part light brown coloured mobile
liquid, used for brush application. It is solvent borne to give
rapid drying properties.

Product Details:

Uses:
Renderoc FC is designed for application to minor imperfec-
tions in concrete and masonry surfaces. It is suitable for
application in the range of feather edge to 3 mm, and can be
used in the following situations :

• Filling pinholes prior to overcoating
•  General reprofiling over large areas, up to 3 mm depth
•  Fairing coat, in association with other Renderoc mortars

Advantages:

•  Cost effective - no independent primer necessary
•  Time saving - curing not necessary
•  High performance - excellent bond to the substrate

Description:
Renderoc FC is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a highly consistent cementitious mortar. Renderoc FC exhibits excellent thermal compatibility with concrete, and is fully compatible with other Renderoc mortars.

Product Details:

Uses:
 Brushbond RFX is an high performance elastomeric cementious coating used for waterproofi ng and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water.
Brushbond RFX is suitable for all types of structures including those in coastal environments. The product can be used on concrete, brick and blockwork sub- strates and is equally suitable for new and existing structures. The product is designed to reface and even out variations in concrete and masonry surfaces and bridge shrinkage cracks. It provides a seamless, fl exible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements, roofs, toilets & wet areas. The product provides a tough durable water resistant coating which can withstand light pedestrian traffi c and also has excellent weather resistance for exterior applications.

Advantages:

• Ex celle nt b arrie r to carbo n dioxide, chloride
• and sulphate ions.
• Allows water vapour to escape from the structure.
• Waterproof-suitable for water retaining structures.
• High resistance to the effect of long-term weathering,
• durable in all climate conditions including UV attack.
• Non toxic - ideal for potable water tanks.
• Flexible, with thermal expansion similar to concrete.
• Excellent bond to concrete and masonry.
• Good crack accommodation capacity.
• Minimum surface preparation needed and low labour