Fosroc Renderoc RG

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

Uses:
Lokfix are used for high strength corrosion resistant anchoring of bolts and bars from 12 - 51mm diameter into concrete, rock, masonry or brickwork where high speed of installation and early application of load is required.
Permanent installation of reinforcement starter bars, foundation bolts, base plates, balustrading, barriers and safety fences, railway tracks, tie-back anchors, reinforcement dowelling abutments, ground anchors for towers, cranes, dock sills.

Advantages:

• Rapid strength gain
• Vibration resistant
• Corrosion resistant
• Non expansive

Description:

The three versions of Lokfix polyester resin grout are all pre-
measured, two part, filled polyster resin grouts. After
hardening the grout produces anchorages of consistent
reproducible values.

Product Details:

Uses:
Nitotile GPX is a high quality adhesive for the permanent fi xing
of ceramic tiles. It can also be used for fi xing of insulating and
acoustic boards based on expanded polystyrene etc. Typical
uses include :

• Wet areas - kitchens and bathrooms
• Tile claddings

Advantages:

• Tropical grade to suit Indian working conditions
• Good open wet time
• Good slip resistance
• High adhesion strength
• Water proof

Standards Compliance:
Nitotile GPX conforms to BS 5980 Class AA & B Type 1 and
suitability for contact with potable water as per BS 6920 Part 1.

Description:
Nitotile GPX cementitious powder is available in grey or white
colour.

Product Details:

Uses:
Dekguard Standard system is suitable for use on all types of structures which are not directly exposed to sea, to protect structures from attack by acid gases, chloride ions, sulphates, oxygen and water. The product is also suitable to protect other cementitious substrate and masonry.

Advantages:

• Protects exposed reinforced concrete structures from atmospheric gases - excellent barrier to carbon dioxide, chloride ions, sulphates, oxygen and water.
• Breathable - Allows water vapour to escape from the structure. But does not allow water vapour to penetrate the structure.
• UV resistant - aliphatic acrylate gives resistance to long term weathering.
• Single pack - Ease of application, can be applied with
• brush or airless spray.

Description:
Dekguard Standard system comprises of a single component, penetrating silane/siloxane primer and a single component aliphatic acrylate, solvent based top coat, providing resistance to aggressive agents, UV rays and rain. Dekguard Standard system is supplied in ready to use packs and is available in a range of colours

Product Details:

Uses:
Nitoflor TF5000 provides an extremely high strength floor topping with exceptional resistance to the surface mechanical wear and attack from chemical spillage, is impervious and, at the same time, has a safe non-slip finish for personnel and vehicular traffic.

Ideally suited for heavy engineering plants, chemical handling and process areas, steelworks, dairies, breweries, oil refineries, paint workshops, battery rooms, plating factories, sugar and food industries.

Advantages:

• Durable : Exceptional resistance to abrasion and to a wide range of chemicals
• Non-slip : Good gripping surface to both vehicular and pedestrain traffic
• 5mm, minimal: No interference with exist thicknessing levels.

Description:
Nitoflor TF5000 is a three part solvent-free combination of
epoxy resin, modified amine hardeners filled with specially
graded and selected high crushing strength, chemically inert
aggregates.

Product Details:

Uses:
To provide a hard wearing, easily cleaned, attractive floor coating in areas where high resistance to chemical attack is required. It is suitable for use in production assembly areas, workshops, dairies, soft drinks production and bottling plants, kitchens, showrooms etc. It is particularly suitable in wet working areas and where chemical spillage is likely, e.g. plating shops, processing plants, dye works etc.

Advantages:

• Hard wearing - durable, low maintenance costs
• High resistance -to a wide range of industrial chemicals
• Hygienic - impervious finish provides easily cleaned surface
• Attractive - available in a range of colours to improve the working environment.

Description:
Nitoflor FC140 is a three component solvent based, epoxy resin coating system supplied in pre-weighed packs ready for on-site mixing and use.
The cured film forms a hard but flexible coating with excellent adhesion to clean concrete, sand/cement and granolithic screeds, and certain metal surfaces. It cures to a semi-gloss, impervious finish which is easily cleaned.
The product is available in a range of standard colours and is also available in a clear grade.

Product Details:

Uses:
Provides an economical method of levelling floors prior to laying epoxy screed, toppings or coatings such as Nitoflor FC140* † , Nitoflor FC150* † and Nitoflor SL2000.

Advantages:

• Cost effective
• High strength
• Quick and easy to lay
• Seamless
• Durable

Description:
Nitoflor EU5 consists of special resins and graded aggregates formulated to withstand chemical attack and impact shock. The product is supplied as a 3 component system comprising resin base, resin hardener and fillers. When correctly laid Nitoflor EU5 will provide a surface ready to receive applications of other Fosroc flooring systems.

Product Details:

Uses:
Nitoflor FC150 provides a hard wearing, chemical and abrasion resistant floor finish. It is ideally suited for use in wet areas where a high degree of resistance to chemicals, oils and grease is required such as :

• Dairies
• Soft drinks production facilities
• Chemical manufacturing plants
• Car parks and workshops

Advantages:

• Durable, low maintenance costs.
• Proven against a wide range of industrial chemicals.
• Solvent free - no odour during application. 
• Slip resistant - different textures available to suit conditions to avoid slipping.

 

Description:
Nitoflor FC150 is a solvent free system based on epoxy resins and curing agents specially selected for their ability to withstand chemical attack. The system consists of pre-weighed base & hardener components and a Nitoflor colour pack, all of which contain reactive elements that are essential to the installation of the system.

Product Details:

Uses:
As a spray applied membrane to retain moisture in concrete for effective curing.
Suitable for all general concreting applications and of particular benefit for large area concrete surfaces, such as airport runways, roads and bridgeworks.

Advantages:

• Improved curing of concrete enhances cement hydration and provides a more durable concrete.
• Control of moisture loss improves surface quality, reducing permeability, producing a hard-wearing, dust free surface and minimising potential for surface cracking and shrinkage.
• Light reflective grades minimise solar temperature gain.
• Spray application reduces labour costs and eliminates the need for alternative curing systems.

Description
Concure LP90(M) concrete curing compound is polymer based continuous film forming curing compound and is supplied as aluminised polymeric resin solution drying to a silver film on application.

Product Details:

Uses:

• Suitable for high performance concrete
• To produce pumpable concrete
• To increase workability without extra water
• To improve cohesion, minimising segregation and give better finsih.
• Chloride free, safe for use in prestressed and reinforced concrete
• Can be used with concrete containing microsilica and other cement replacements.

Advantages:

• Improved workability - Easier, quicker placing and compaction.
• Increased strength - Provides high early strength if water reduction is taken advantage of.
• Increaseded quality - Denser, close textured concrete with reduced porosity and hence enhanced durability.

Description:
Conplast SP430G8 is based on Sulphonated Napthalene Polymers and is supplied as a brown liquid instantly dispersible in water.
Conplast SP430G8 has been specially formulated to give high water reductions upto 25% without loss of workability or to produce high quality concrete of reduced permeability.

Product Details:

Uses:
To accelerate the setting and early strength gain of Portland cement concrete and mortar mixes without the introduction of chloride. Acts as a plasticiser, so gives significant increases in both ultimate and early strengths. Typical applications include precast concrete, concrete placed in cold weather, concrete for repairs, mortars for brickwork.

Advantages:

• Chloride free, safe in prestressed and reinforced concrete.
• Produces exceptionally high early strengths.
• Plasticising action gives increased workability and / or increased strengths.
• Early setting improves frost resistance.
• Suitable for bricklaying mortar mixes.

 

Description:

Conplast NC is guaranteed completely free of all forms of
chloride and is supplied as a light straw coloured liquid.

The main active ingredient is an inorganic formate.

Product Details:

Uses:
Conplast SP430SRV is used where a high degree of workability is required and also as an aid to workability retention where delays in transportation or placing are likely or when high ambient temperatures cause rapid slump loss. To facilitate production of high quality concrete of improved durability and water tightness.

Advantages:

• Speeds Construction : Increased workability reduces placing time, equipment and labour element.
• Self Compacting : Conplast SP430SRV modified concrete is highly fluid and needs little or no compaction.
• Reduced Permeability: Better dispersion, reduces porosity and improves water penetration resistance.
• Reduced Segregation: Increased cohesion minimises segregation and bleeding, improving surface finish.
• Longer Placing Time: Conplast SP430SRV gives greater usable life of concrete at high ambient temperatures because of its unique workability retention potential.
• Improved Pumpability: Increased workability and cohesion aids pumping by reducing line friction, dry packing and slump loss due to temperature.
• Chloride Free: Safe in prestressed, reinforced or marine concrete and compatible with sulphate resisting cement or marine aggregate.

Product Details:

Uses:
Surface retarder for producing exposed aggregate concrete finish in face-up and face-down precast concrete manufacture.

Advantages:

• Economical in application
• Simply applied, straight from the container.
• Need not use a mould release agent
• Good results with heat curing and high temperature concreting.
• Can be used on steel, glass fibre or timber formwork.
• Non-toxic and non-flammable.

Description:

Conplast SR is designed to provide a simple, economical method of exposing aggregates in freshly poured face-up and face-down precast concrete panels or slabs. Conplast SR retards the hydration of cement at the surface matrix of the concrete.

Product Details:

In order to cater to the numerous necessities of the patrons, we have been able to provide a qualitative range of Renderoc RG Cement Additives.

Product Details:

Uses:
For the horizontal sealing and maintenance of joints in concrete roads, concrete runways and hard standings. The excellent fuel resistance of Colpor 200 makes it particularly suitable for sealing areas where fuel and oil spillage might occur such as:

• Aircraft fuelling areas
• Oil terminals
• Garage forecourts
• Parking and cargo areas
• Docks and harbours
• Warehouses

Advantages:

• ¿¿ Cold applied - no heating equipment required
• ¿¿ Fuel, oil and hydraulic fluid resistant
• ¿¿ Self-levelling
• ¿¿ Tough rubbery seal
• ¿¿ High performance - less maintenance

Standards compliance:
Colpor 200 complies with U.S. Federal Specification SS-
S-200E:1984 and British Standard 5212:1990 - types N, F
and FB.

 

Description:
Fosroc Colpor 200 cold applied, two part polyurethane sealant is designed for joints in concrete paved areas. The capability of accommodating cyclic movements is retained by Colpor 200 throughout extremes of temperature conditions.
Colpor 200 is resistant to fuel, oil and hydraulic fluid spillage, will not harden in cold weather nor become excessively soft or pick up in hot conditions. Colpor 200 has high durability and long service life which significantly reduces maintenance costs.

Product Details:

Description of first aid measures:

• General information: Immediately remove any clothing soiled by the product.
• Inhalation: Move affected person to fresh air at once. Rinse nose and mouth with water. Get medical attention if any discomfort continues.
• Ingestion: Remove affected person from source of contamination. Do not induce vomiting. Get medical attention immediately.
• Skin contact: Remove affected person from source of contamination. Remove contaminated clothing. Wash skin thoroughly with soap and water. Get medical attention if irritation persists after washing.
• Eye contact: Remove affected person from source of contamination. Remove any contact lenses and open eyelids wide apart. Remove any contact lenses and open eyelids wide apart. Continue to rinse for at least 15 minutes. Continue to rinse for at least 15 minutes. Get medical attention if any discomfort continues.

Product Details:

Uses:
Fosroc Auramix 200 is a Viscosity Modifying Admixture for
contemporary concrete requirements:

• Self-consolidating concrete. ???
• Pumped concrete. ???
• Sprayed concrete. ???
• Light weight aggregate concrete. ???
• SCC with low fines content. ???
• Concrete with improper gap grading or low binder
• content.

Advantages:

• Reduces sensitivity to variations in moisture content in aggregates. ???
  Eliminate segregation and bleeding in mixes. ???
  Reduces pump pressure by decreasing plastic viscosity of concrete while keeping homogeneity and thereby reducing friction. ???
• Exhibits better passing-ability and pump-ability while keeps high fluid mixes homogeneous.
• No effect on setting time by Auramix V200, set time will be dictated by the HRWR or other admixtures used in mix
• No effect on air entrainments. ??? No effect on fluidity of mixes either in initial stage of the mix or in retention period. ???

Description:
Fosroc Auramix V200 is a chloride free, ready to use liquid admixture. It is a high-performance concrete rheology-modifying agent based on a unique polymer which is designed to be used with Fosroc’s polycarboxylate based Structural and Auramix admixtures for high fluid concrete.

Product Details:

Auramix 400 is a high-performance superplasticiser intended for applications where high water reduction and long workability retention are required, and it has been developed for use in:

• Self-compacting concrete,
• Pumped concrete,
• Concrete requiring long workability retention,
• High performance concrete.

Advantages:
Low viscosity suitable for pumping of different grades of
concrete to higher floors.

• Higher E modulus
• Improved adhesion to reinforcing and prestressing steel
• Lower permeability
• Better resistance to carbonation
• Better resistance to aggressive atmospheric conditions

Description:

Auramix 400 is a unique combination of the latest generation superplasticisers, based on a polycarboxylic ether polymer withlong lateral chains. This greatly improves cement dispersion. At the start of the mixing process an electrostatic dispersion occurs but the cement particle’s capacity to separate and disperse.This mechanism considerably reduces the water demand in flowable concrete.

Product Details:

Uses:
 Used to enable a high build of sprayed concrete, shotcrete and gunite. It provides set acceleration and reduces rebound.

Advantages:

• Low rebound due to controlled set
• No adverse affect on strength
• High build up with minimal slump ensures faster coverage rates
• Safe to handl

Description:
Sprayset HBP is a chloride free non-caustic admixture for sprayed concrete, shotcrete and gunite. It is supplied as a powder which is added to the mix to impart properties of high build and low rebound.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

 “Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

Uses:
For filling blow holes, making good slightly damaged concrete, eliminating minor irregularities on floors and walls prior to applying Nitoflor and Nitocote epoxy coatings.

Advantages:

• Easy to apply and finish
• Consistency can be adjusted by varying the filler content
• Non-slump, can be applied to vertical surfaces and trowelled into blow holes
• Reduces consumption of subsequent coatings
• Chemical resistant

 

Description:

Nitocote VF is a thixotropic, solvent free, three component compound based on epoxy resins, graded fillers and thixotropic agents. It is applied directly to concrete for filling cracks, blow holes etc., which cures to a surface ready for subsequent coatings.

Product Details:

Description:
Primer 20 is a high performance single component chemically active, non-toxic liquid for brush application to prime porous surfaces.

Advantages:

• Easy to Apply
• Strong adhesion

Application:

• Open tin lid. Mix thoroughly until a homogeneous dispersion
• is achieved.
• Apply one thin coat using a clean dry brush. Avoid over application of primer causing puddles in the bottom of the joint. Sealants should be applied between 30 minutes and 4 hours after priming when its tack free.

Product Details:

Description:
Nitoflor SL2000 consists of graded aggregates bound in a pigmented epoxy resin binder. It is supplied as a four component system, pre-weighed for on-site mixing. When laid, it provides a smooth, light-reflective surface. It is available in a range of standard colours.

Surface Preparation:
It is essential that Nitoflor SL2000 is applied to sound, clean
and dry surfaces in order that maximum bond strength is
achieved between the substrate and the flooring system. All
dust and debris should be removed prior to application of the
product or its primer.

New concrete floors:
New concrete, or cementitious substrates, should be at least
28 days old and have a moisture content not exceeding 5%.
Laitance deposits on new concrete are best removed by light
grit blasting, mechanical scabbling or grinding.

Old concrete floors:
Existing concrete floors which require refurbishment must be
prepared to ensure a strong adhesive bond between the
flooring system and the existing floor. Mechanical cleaning
methods are strongly recommended particularly where heavy
contamination by oil and grease has occured or existing
coatings are present. To ensure adhesion, all contamination
should be removed.

Product Details:

“Jai Shree Radhey Shyam Enterprises ” are engaged in Wholesale Trading a wide assortment of Construction Chemical, Chemical Primer, Concrete Admixture, Waterproof Coating, etc.

Product Details:

Storage:
Nitoprime 25 has a shelf life of 12 months when stored in unopened containers under normal warehouse conditions.

Precautions:

Health & Safety instructions:

Nitoprime 25 should not come into contact with skin and
eyes or be swallowed. Avoid prolonged inhalation of solvent
vapours.
Some people are sensitive to epoxy resins, hardeners and
solvents. Gloves, goggles and barrier creams should
therefore be used while handling the product. Adequate
ventilation should be ensured and if working is enclosed
areas, suitable breathing apparatus must be used. If the
resin comes in contact with skin, it must be removed before
it hardens with a resin removing cream, followed by washing
with soap and water - solvent should not be used.


Additional Information:
In addition, the Nitoflor range of industrial flooring products
include concrete hardeners, resin floor coatings, toppings
and screeds designed to meet most requirements of modern
industrial environments. For further information contact the
local Fosroc office.

Product Details:

Uses:
For spraying on freshly cast concrete, or newly exposed concrete surfaces after removal of form work, to form a temporary membrane which will retain sufficient moisture for effective curing to take place. Used for concreting generally but especially useful for large areas of concrete such as pavements, runways and bridge decks; also for vertical or sloping surfaces as on towers, chimneys, canal linings, columns and beams, where water curing is difficult or unreliable.

Advantages:

• Single application : Forms moisture barrier for whole of the curing period.
• No other curing necessary : Eliminates use of water, hessian or sand, completely.
• Reliable : No risk of erratic or poor curing and ensures that cement hydrates efficiently.
• Ensures hard-wearing surface : Minimises risk of drying shrinkage, cracks and dusty surfaces.
• Easy and safe spray application:  Non-toxic and nonflammable.

Standards compliance:
Curing efficiency : Concure WB curing agent complies with
the internationally recognised ASTM C309-90 standard.

 

Description:
Concure WB is a white, low viscosity wax emulsion which incorporates a special alkali reactive emulsion breaking system. This system ensures that the emulsion breaks down to form a non penetrating continuous film immediately upon contact with a cementitious surface. This impervious film prevents excessive water evaporation which in turn permits more efficient cement hydration, thus reducing shrinkage and increasing durability.

Product Details:

Description of first aid measures:

• General information: No specific recommendations. Move affected person to fresh air and keep warm and at rest in a position comfortable for breathing.
• Inhalation: Move affected person to fresh air and keep warm and at rest in a position comfortable for breathing. Keep affected person under observation.
• Ingestion: Never give anything by mouth to an unconscious person. Do not induce vomiting. Rinse
• mouth thoroughly with water. Get medical attention if any discomfort continues.
• Skin contact: Remove affected person from source of contamination. Remove contaminated clothing immediately and wash skin with soap and water.
• Eye contact: Remove any contact lenses and open eyelids wide apart. Continue to rinse for at least 15 minutes.

Product Details:

Effects of Overdosing:
An overdose of double the intended amount of Sprayset HBL(M) will result in increased setting of the mix before it reaches the surface to be sprayed. It will also result in a loss of strength.

Storage Conditions:
Store in dry conditions in the original, unopened container. If stored at high temperatures, the shelf life may be reduced.